Millipore Sigma Vibrant Logo

Colector de vacío MultiScreenHTS

For vacuum filtration of 96 and 384 samples

Recursos relacionados

Descripción

Especificaciones

Información para pedidos

Documentation

Referencias bibliográficas

Visión general referenciasAplicación
Method for Simultaneous Measurement of Antibodies to 23 Pneumococcal Capsular Polysaccharides
Raymond Biagini, Sonela Schlottmann, Deborah Sammons, Jerome Smith, John Snawder, Cynthia Striley, Barbara MacKenzie, and David Weisssman
Clinical and Diagnostic Laboratory Immunology September 2003, p 744-750, Vol. 10, No. 5  2003

A non-radiolabelled ferriprotoporphyrin IX biomineralisation inhibition test for the high throughput screening of antimalarial compounds.
E. Deharo, R. N. Garcia, P. Oporto, A. Gimenez, M. Sauvain, V. Jullian and H. Ginsburg
Experimental Parasitology 100 (4): 252-256  2002

Use of Multiscreen plates for the preparation of bacterial DNA suitable for PCR
Reek FH, Smits MA, Kamp EM, Smith HE
Biotechniques. 1995 Aug;19(2):282-5  1994

PCR
High-Throughput Microplate Format for Producing and Screening Riboprobes from Bacterial Cells
Matthews, P.D. and Wurtzel, E.T.
BioTechniques. 18: 6, 1000 – 1004  1994

Nucleic Acid Purification and Concentration

Preguntas frecuentes

PreguntaRespuesta
Can I alcohol sterilize my Multiscreen Manifold and Plates?Note: This procedure does not work for the nitrocellulose based membrane plates such as HATF. (For use on: Durapore PVDF, Biopore, and glass fiber filters).

MultiScreen Alcohol Sterilization Protocol
Additional Materials Required:
1. 70% Reagent grade ethanol (with NO added denaturation agents)
2. Suitable sterile support or container to place the plate(s) inside or alternatively on for incubation. A sterile material such as a lid can be used, although the support trays supplied with pre-sterilized MultiScreen plates are ideal.
3. Sterilized water or buffer.
4. Sterilized (5x9” or 4x6”) gauze or sponges for blotting the underdrain.

Procedure (To be performed in Laminar flow hood under aseptic conditions):
1. Thoroughly rinse, fill, and expose all surfaces of the Vacuum manifold to 70% Alcohol and incubate 5-15 minutes. Turn on vacuum to remove excess alcohol.
2. Place MultiScreen plate to be sterilized on top of the vacuum manifold and completely fill with 70% alcohol. Be careful to expose all surfaces to the alcohol and allow to incubate 5-15 minutes. Additional plates can be sterilized by placing on a lid or other suitable object during incubation.
3. Turn on vacuum to remove excess alcohol, tip plate to drain excess alcohol into vacuum manifold, blot on sterilized pad, and place on lid to air dry overnight in laminar flow hood.
4. Turn on vacuum and remove all of the alcohol, add sterilized water to inside of manifold to remove residual alcohol. Allow entire unit such as the steel support and gasket to air dry under the hood with the top removed. The manifold can be stored in the hood and used as required.

Note: The MultiScreen lids can also be sterilize by this procedure.

Cautions:
1. Do not allow alcohol to remain inside vacuum manifold, it should be rinsed each day with sterile water.
2. This procedure does not work for the nitrocellulose based
I broke the tubing adapter on my MultiScreen manifold. Is there a replacement part?Yes, this piece can be purchased as part of the Repair Kit, catalog # MAVMXXA03. It's important to point out that in many cases a broken adapter result from improperly cared for manifolds. Always rinse manifold with water after its use in an assay (especially TCA precipitation assays).
What plates can be used with the MultiScreen HTS manifold (Catalogue number MSVMHTS00)?All MultiScreen HTS platform filter plates, Solvinert and Solvinert Deep Well plates can be used with the HTS manifold.
Can the classic MultiScreen plates be run on the HTS manifold?Only in filter to waste mode. The HTS plates should be used with the HTS manifold for the most benefit.
Can the MultiScreen HTS manifold be used with Millipore's genomics application plates (plamid prep, pcr cleanup, sequence reaction clean up)?Filter to waste modes work, but not filtrate collection, so using the clearing plate with the plamid plate will not work. Millipore's genomics plates have not been validated on the HTS manifold. Please contact technical service for more information at 1-800-645-5476.
If using the MultiScreen HTS manifold, when do I have to use the droplet trap array?The droplet trap array should be used when filtering a 384 well plate to waste.
If the deep well collar sold with the MultiScreen HTS manifold or is it sold seperately?The deep well collar is sold as an accessory to the MultiScreen HTS manifold; it does not come with the manifold. The catalogue number is MSVMHTS0D.
When using the MultiScreen HTS manifold, can I filter to waste when using a shallow well plate?Yes. The classic grid should be in place for removeable underdrain HTS plates or the collar gasket frame should be in place for Solvinert plates.
When using the MultiScreen HTS vacuum manifold, can I filter to waste when using a deep well plate?Yes. The deep well plate should be placed on top of the manifold collar with the clear gasket support installed.
When using the MultiScreen HTS manifold, how can I test to see if the manifold is properly installed and/or that I have enough vacuum for my application?The easiest way to test the manifold and/or set vacuum pressures is to put the collar on the base with nothing inside and place a collection (plastic bottom) plate on the top. You can now adjust the vacuum to the desired level.
Show more

Productos y aplicaciones relacionados

Familias de productos

Unidades de filtración Millex

Las unidades de filtración Millex con membrana hidrófoba Fluoropore son idóneas para la esterilización.
Más información >>

Productos relacionados por: Application Facete

Protein Purification
Sample Preparation
Dialysis and Filtration

Productos relacionados por: Brand Facete

MultiScreen™

Categorías

Life Science Research > Cell Culture and Systems > Cell Culture Flasks, Plates, & Slides > Multiwell Plates