In-Line Stainless Steel Filter Holders (25 and 47 mm)
Recommended Products
-
106444 SAFC Sodium chloride -
HS260/4XS-N2 Millipore HST260 DRIVE UNIT, 7.5 KW, IE2, CE+ -
8202590005 Sigma-Aldrich 1,4-Dihydroxyanthraquinone -
8147271000 Sigma-Aldrich Brij® 58 -
109477 Supelco Buffer solution -
KVGLA04TH3 Millipore Opticap® XL4 Durapore® 0.22 µm 1-1/2 in. TC-9/16 in. HB -
125158 Millipore RoboColumn Eshmuno® CPX 0.2ml -
KWLCA02FF3 Millipore Opticap® XL2 Milligard® Low Protein Binding 1.2/0.5 µm 3/4 in. TC/TC -
820598 Sigma-Aldrich Dodecyl 3,4,5-trihydroxybenzoate -
ABS1849 Sigma-Aldrich Anti-phospho-Rsk1 (Thr359/Ser363) Antibody
개요
사양
주문 정보
Documentation
FAQ
| Question | Answer |
|---|---|
| I just purchased one of your stainless filter holders and after only a few uses it is starting to rust. Is the unit defective? | Rusting of stainless steel holders can usually be attributed to high iron content in the water. Iron deposits create rust "stains" that can be removed with non abrasive cleaners or sometimes fine steel wool. All stainless steel can rust over time. It should be washed with DI water and dried thoroughly immediately after each use. |
관련 제품 및 어플리케이션
제품 패밀리
Peristaltic PumpsA variable-speed (60–600 RPM) pump drive allows flow rates ranging from 480 to 1,680 mL/min, depending on pump head selected.더 보기 >> |
Dispensing Pressure VesselsFor dispensing liquid volumes up to 20 L더 보기 >> |
MF-Millipore™ Membrane FiltersMixed cellulose esters더 보기 >> |
관련 제품: Application Facete
| Sample Preparation |
| Dialysis and Filtration |
카테고리
| Reagents, Chemicals and Labware > Lab Filtration > Filter Holders and Accessories |
Applications
For filtration of gases or liquids at inlet pressures of 20 to 700 bar. Differential pressure depends on filter type used. All filter holders may be autoclaved. Filter holder XX44 047 00 is equipped with a back-pressure support screen. It may be autoclaved with filter in-place, if PTFE-coated support screens, XX44 047 02 and XX44 047 04, are used. Holder XX45 047 00 may be equipped with an upstream filter support screen, XX45 047 04, for back-pressure
protection of filter.
)
47 mm high pressure filter holder, XX45 047 00.
| Replacement Parts | |
| 1 | Inlet/Outlet Adapter |
| 2 | Adapter O-ring |
| 3 | Hex-cap Screw |
| 4 | Top Plate |
| 5 | Inner O-ring |
| 6 | Outer O-ring |
| 7 | Filter Support Screen, 47 mm, stainless steel |
| 8 | Bottom Plate |
| Specifications | |||
| 25 mm HP Holder | 47 mm Holder | 47 mm HP Holder | |
| Materials | |||
| Housing | Stainless steel | Stainless steel | Stainless steel |
| Gaskets | Nitrile (NBR) | Silicone (SI) | Fluoroelastomer (FKM) |
| Filter Diameter | 25 mm | 47 mm | 47 mm |
| Filtration Area | 2.2 cm² | 13.8 cm² | 9.6 cm² |
| Prefilter Diameter | 10 (thick depth prefilter ) | 22 (thick depth prefilter ) | 42 (thick depth prefilter ) or 47 (membrane prefilter) |
| Maximum Pressure Differential, bar gauge (psig) | |||
| With 3.0, 5.0 and 8.0 µm MCE filters | 10.3 (150) | – | 10.3 (150) |
| With all membrane filters except 3.0, 5.0 and 8.0 µm MCE filters | 69 (1000) | – | 103 (1500) |
| Maximum Inlet Pressure, bar (psi) | 345 bar (5000 psi) | 19 bar (275 psi) | 689 bar (10,000 psi) |
| Dimensions | |||
| Height | 3.2 cm | 2.7 cm | 4.4 cm |
| Diameter | 5.1 cm (2.0 in.) | 7.6 cm | 8.6 cm |
| Fittings | |||
| Inlet | 1/8 in. NPTF | 1/4 in. NPTF | 7/16 in.-20 (UNF-3B) female |
| Outlet | 1/8 in. NPTF | 1/4 in. NPTF* | 7/16 in.-20 (UNF-3B) female** |
| *1/8" NPTF upstream port with pipe plug **Adapters to 1/4" NPTF are included |
|||