Millipore Sigma Vibrant Logo
Attenzione: Ci siamo trasferiti. Non è più possibile acquistare i prodotti Merck Millipore nel sito MerckMillipore.comPer saperne di più
 
Ricerche life science
 

Sample Preparation and Gel Electrophoresis

 Request Information
Related Resources: Brochures | Application Notes
Electric currents, wires, leads, combs, leaks… so many opportunities for trouble. But we still use gels, because electrophoresis remains an effective way to separate proteins — so that the results of antibody-based immunodetection can be fairly unequivocal.

Click on the Sample Preparation and Gel Electrophoresis topics to read about the possible causes and remedies:

No Bands or Gel Front

Possible CauseRemedy
Proteins have run off the gel
  • Decrease the amount of time the gel is run.
  • Decrease the voltage.
  • Ensure that the leads are in the correct orientation, as the electrophoresis leads to the power supply may be reversed, causing the gel to run upward.
  • Increase the acrylamide percentage of the gel.
Not enough protein was loaded on the gel
Sample has diffused away from the well prior to applying power
  • Decrease the time between loading the first well of the gel and beginning electrophoresis. If necessary, run fewer gels and/or fewer lanes at once.
Not enough SDS in the sample
  • Without adequate SDS, the proteins are not negatively charged and will not travel through the cell. Ensure adequate SDS concentration.
Back to Top

Sample Doesn’t Sink to the Bottom of the Well

Possible CauseRemedy
Not enough glycerol in sample
  • Increase glycerol concentration.
Back to Top

Sample Leaking Out of Well

Possible CauseRemedy
Wells damaged during comb removal
  • Remove gel comb carefully to avoid disruption of the wells. Rinse wells gently with electrophoresis buffer prior to sample loading to detect damaged wells.
Wells damaged during sample loading
  • Load sample carefully, ensuring that pipette tip does not touch the bottom or sides of the wells.
Back to Top

Bands Are Smeared Vertically

Possible CauseRemedy
Incomplete protein solubility blocks proteins from entering the gel
  • Ensure adequate sonication/homogenization and centrifugation during cell lysate preparation to remove particulate matter.
Protein degradation
  • Add/increase concentration of protease/phosphatase inhibitors during cell lysate preparation.
  • Explore inhibitor cocktail options
  • Avoid repeated freeze/thaw cycles of cell lysate and Western blot samples.
Too much protein loaded

Effect of loading too much protein on SDS-PAGE (rightmost lane)
Effect of loading too much protein on SDS-PAGE (rightmost lane)
 
Gel run too fast
  • Increase gel run time.
Poor quality or old gel
  • Use a fresh gel.
Back to Top

Too Many Bands

Possible CauseRemedy
Protein degradation
  • Add/increase concentration of protease/phosphatase inhibitors during cell lysate preparation.
  • Explore inhibitor cocktail options
  • Avoid repeated freeze/thaw cycles of cell lysate and Western blot samples.
Protein aggregation
  • Ensure adequate DTT concentration, which reduces disulfide bonds.
  • Heat Western blot samples in water bath prior to loading onto gel.
  • Order OmniPur® DTT
Back to Top

Gel Running Unusually Slowly

Possible CauseRemedy
Buffers too concentrated
  • Dilute buffers.
Current too low
  • Increase voltage of gel apparatus.
Back to Top

Gel Running Unusually Fast

Possible CauseRemedy
Buffers too dilute
  • Concentrate buffers.
Current too high
  • Decrease voltage of gel apparatus.
Back to Top

Protein Bands Too Close Together (Not Completely Resolved)

Possible CauseRemedy
Insufficient run time
  • Run gel for longer period of time.
Incorrect gel pore size
  • Use a gradient gel (higher acrylamide percentage on bottom than top) that will adequately resolve a broader size range of proteins.
Back to Top

Leftmost and/or Rightmost Bands of the Gel are Distorted

Possible CauseRemedy
Edge effects
  • Do not leave empty wells. Load wells not being used with a small amount of protein to prevent edge effects on neighboring lanes.
Back to Top

Bands Form Smiling Shapes

Possible CauseRemedy
Excessive heat

Gel run is “smiling.” This is caused by too high a voltage. Also, target bands are bleached, caused by using the detection reagent at too high of a concentration.
Gel run is “smiling.” This is caused by too high a voltage. Also, target bands are bleached, caused by using the detection reagent at too high of a concentration.
 
  • Run gel at a lower voltage for longer time. Use chilled buffers and run gel in a cold room or packed on ice.
Back to Top